I think that settles it for us, we’ll likely take it to a framers when we get home. I’m a bit scared to try and dismantle it myself.
Thank you for the advice!
I apologize if this isn’t the correct community ask, but i was hoping for a bit of help getting this frame cleaned up.
My wife and I picked this piece up today. There’s some water damage and i’m wondering what the best way to clean the fabric matting would be or if we should get it replaced.
For those curious it looks like the artist is Edward Aldrich. We think its an oil painting and from the date we’re guessing its from 97.
Thanks everyone!
P.S. I took a look through the community and the art here is amazing!
I’m considering an a change at point as well. The v2 has been great but finicky is a perfect description. Any reason you were thinking Bambo Labs instead of a Prusa?
Of course! This should be the original link. I think my issue was slightly different, but hopefully this helps. My stepper motors were over heating and skipping steps. If it looks like that might solve your issue, this article helped with my ender 3
Thank you! I appreciate it!
Thank you guys for pointing out the vref issue in my last post! I got it adjusted, and they were all fairly high so now they should be dialed in. While I was in there, I figured I should probably calibrate the extrusion steps as well.
I’ve got a couple larger projects coming down the pipeline. But if I can go off of this cube, I think I’ll be in good shape.
Oh man, you should have seen me looking for the HDMI ports. I was very confused until I realized my mistake. Turns out that there’s more than one kind, who knew🤷
I’ll have to give that camera connection a second look lol
Damn does this mean I have to buy another raspberry pi or can the one running octoprint serve double duty?
I just picked up a pi4 b today and was tinkering with octoprint.
So far it looks great, i just haven't figured out how to get the pi camera module 3 working quite yet. The stream from octoprint just constantly tries to load.
I’m excited to try some prints with it soon!
No, that’s a new one.
Would greasing my gantry screw help?
If I’m missing steps due to heat is the only solution a new motherboard?
I have! This printer actually finished a 3ft sailboat rudder before this print. I popped some pictures of it in as well
Do you think that could be be solved by adjusting the z offset?
Thanks for the tip! I’ve been hesitant to start messing around to much but I think it should if it means it’s more reliable
I’ve been looking at this for a while. The camera I have on it is a security camera that i put on my desk while it prints if I’m gone.
Do you think its worth pulling the trigger on a raspberry pie to get this set up?
I left the print over the weekend and I came back to spaghetti. It looks like something, caused the printer to push the print off its base like it was a poorly leveled bed?
I still have to watch the camera footage to see what failed, but I hope you guys get a chuckle out of the spaghetti monster like I did.
Yes, I just finished printing a rudder core for my sailboat.
For all the headache its caused, its also saved me from several trips to the store to find cable ties, chip clips, a hair dryer holder, pencil cups, spice racks, etc.
Sweet thank you!
How’s Freecad these days? I avoided awhile ago it because it looked difficult to use but I think this might push me over to it
This right here is the only thing I’m worried about
I wasn’t saying that playstation hasn’t sold more consoles. I also not arguing that it doesn’t have better games. It does, Microsoft is very clearly dropping the ball even after they acquired as many heavy hitters as they did. My biggest regret this generation was switching to a Series X from the PS4 instead of either tossing money at a PC or picking up the PS5.
What I’m surprised by is that the conditions when consoles have had didn’t seem to be taken into effect.
I find poor sales hard to believe taking into account the pandemic and supply chain issues both consoles faced for a couple years.
Hi everyone!
I'm curious to know which slicer you guys use.
I've been using the Creality slicer, but it seems like it pretty consistently crashes, and I've tried Cura but the print seemed stringy despite using the same settings.
How are Orca or Prusa?
Does this hobby ever get easier or is it always like getting kicked in the nuts by Ronaldo?
Filament some how leaked up and burned on. I just don’t have it in me to keep tinkering. I just want to print
Is there any reason that little silver part of the extruder wouldn’t move and start clicking while printing when printing at 205 in PLA. It seems to turn just fine without any filament in there otherwise.
I cleaned out a nozzle clog, but is it possible there’s junk in the hot end stuck?
Resolution: Thanks for your help everyone! It ended up being a nozzle clog that I didn’t get all the way out. I ended up heating the printer up and doing the cool down trick. That seemed to work as a last ditch effort before buying a new nozzle.
Hi all! I was curious to see if anyone had any recommendations for an enclosure for the Ender V3 Neo. I found a few on Amazon, but they look like grow tents and wasn’t sure if that would work well. For a bit of context, it seems like an enclosure is a must have for ABS printing which is ultimately what I’m after.
Thanks everyone!
I recently picked up an Ender 3 V2 Neo at auction. All the pictures looks great, I was told it functioned, and I saw some pictures of it put together.
Long story short either they didn't include the bolts to mount the screen/gantry or kept them.
Does anyone know what screen bolts and gantry mounting bolts I need? Thanks in advance!
It looks like we have a couple perks, but is it going to be viable until the late game?
We loaded up the Hunter 170 today to see how she would sail when loaded down with camping gear in preparation for next weekend’s trip to the Apostle Islands.
My wife is still a bit nervous, but feeling much more confident after today. Please ignore the watering can. She wanted to put a bit more weight onboard just in case.