Skip Navigation
Issue with Klipper on Creality Ender 3 S1 Plus
  • I had a similar issue when I initially installed Klipper on my Ender 3 S1 (not the plus). It would not connect unless I fully restarted Octoprint whenever I turned on the printer. The change I needed to make was go into settings in Octoprint (though I assume its similar on other front ends), and add the following settings:
    Serial Port: /tmp/printer
    Baud Rate: 11520

    If that is not the case for you, try to add some more details. Do you have the config file correct?

  • Constantly Adjusting Z Height Offset
  • Shouldnt be the filament then. I would make sure the probe is fully secured like the other comment suggested. Good luck, that sounds frustrating! I need to adjust mine, but usually after printing for a couple weeks.

  • "Wood" staining, sanding, and clear coating?
  • Oh dang, I misread another comment you made. With regular stain the longer you leave on usually the darker it just makes it appear. But as long as you fully wiped off the excess after it should have worked out. That said I've only used stain on actual wood. Haven't tried printing wood PLA yet.

  • What are some (realistic) things you wanted to get for a while, just for fun?
  • Great for fixing items around the house. Anything that is plastic or could be replaced with plastic can usually be printed. Also great for hardware and jigs. I've had mine for a bit over a month now and have been constantly running it. Check out printables or thingiverse to get an idea of what people are printing. Both are websites people upload models to.

  • "Wood" staining, sanding, and clear coating?
  • I think that might be your issue. Gel stain from minwax should be wiped off after 3 minutes. Anything longer can cause the issue you are experiencing. I would try to wipe/sand off the finish and start again. On a side note, we need to do that to our banister/railing in this house. The previous owner of the house apparently liked the THICK look of the gel stain.

  • 16-year-old girl stabbed to death by another teen during McDonald's sauce dispute
  • We make a homemade version of the canes sauce. It's just a bunch of standard condiments. Before that I had family mail me bags of it from Zaxby's (same sauce). They would sell them massive camelback like bladders full of sauce.

  • [Bob Nightengale] Stephen Strasburg is officially retiring from the Washington #Nats
  • Well so much for that thought: [Bob Nightengale] Stephen Strasburg will continue be paid $35 million annually through 2026 (with about $11.4M deferred each year). He then will receive $26.6M in 2027, 2028 and 2029 in his owed deferred payments. The contract was not insured, leaving the #Nats on the hook for its entirety.

  • [Bob Nightengale] Stephen Strasburg is officially retiring from the Washington #Nats
  • That is a lot of money to leave on the table - I wonder if he worked something out with the Nats for a buyout. If not, this is great for the future of the Nats. Opens up a significant amount of cash the next few years.

  • [Bob Nightengale] Stephen Strasburg is officially retiring from the Washington #Nats

    Stephen Strasburg is officially retiring from the Washington #Nats, as @barrysvrluga reports. He is in the 4th year of a seven-year, $245 million contract.

    4
    InitialsDiceBearhttps://github.com/dicebear/dicebearhttps://creativecommons.org/publicdomain/zero/1.0/„Initials” (https://github.com/dicebear/dicebear) by „DiceBear”, licensed under „CC0 1.0” (https://creativecommons.org/publicdomain/zero/1.0/)NE
    neal33 @lemm.ee
    Posts 1
    Comments 29