The bees would still overcome the wasp, assuming it's a large hive. The wasp will have practical limitations on the amount of ammunition for the weapon (also the question of whether it can reload before getting swarmed) and the ceramic armour won't help against the bees massing together to form a ball of bees around the wasp and overheating it until it dies.
Edit: Apparently it depends on the type of bees as to whether they do the heat ball of death thing, so your mileage may vary.
As in plasterboard sheets? I don't see why not if hand loading, plenty of vans will fit a 2400x1200 sheet (my Transporter fitted a bunch of plywood with room to spare). Loading one with a forklift is harder due to no side access long enough to fit 2400mm but that's a problem shared with tub back utes. If however your plasterboard pallet is side accessible a van with barn doors (like you'd buy if pallets were a priority) will allow you load it in fine.
The old boat also has a motor, note how it's still moving in the photo while the only person in it is in the back holding a tiller (and appears to be facing forwards).
The thinking involved in driving a manual is very minimal once you get used to it, so I reckon any safety issues caused by that would be outweighed by a reduction in the unfortunately common situation of unintended acceleration crashes. You are lot less likely to drive through the nearest wall (or kids) if your instinctual reaction to moving when you should not be is to also go for the clutch and cut power instead of just pressing harder on the wrong pedal.
They have a clutch, but once you're moving it is possible to shift a manual transmission without using the clutch. What you need to do is first take off the load currently passing through the box (if power is being transmitted either direction it holds the engagement dogs in place), so if accelerating you quickly let off the throttle and if decelerating you quickly tap the throttle. This lets you move into neutral, once in neutral you increase or decrease the engine revs to near (ideally exactly) what they would be in the gear you want to shift into at your current road speed, and holding those revs you can then shift smoothly into the new gear.
It is not something I would recommend unless in a jam with synchromesh transmissions (e.g. regular cars, light trucks) as most people aren't going to get it exactly right every time and will just burn out the synchros. If you're unfamiliar with the term these are the parts of the transmission that let you shift from one gear to another in one motion without having to stop in neutral, let the clutch out, and increase/decrease the engine revs to suit your desired gear before clutching in and shifting into it.
Clutchless shifting can and does work well in non-synchro transmissions (e.g. motorbikes, many heavy trucks) once you get the knack, as these transmissions are both more forgiving of not being exactly rev matched and will provide a strong auditory signal if you don't get it close enough (i.e. you'll know if you got it right or not so won't half arse it). Many motorbikes now actually automate this process with devices known as quickshifters - named so because even when doing it by hand clutchless shifts on a bike are noticeably faster than using the clutch.
I find it a bit amusing that the sepia toning effectively colourised the image.
The sun would be the most obvious choice for such a reference point, though it'd be amusing to make it Greenwich and therefore make everyone deal with Earth's rotation and orbit if they want extremely precise calculations (though I expect there wouldn't really be a practical difference on that scale).
The design of the front forks also assists with stability - having some rake and trail means the front wheel has a tendency to self centre (particularly at speed).
Reading the news while having breakfast, though it's now on my laptop instead of the newspapers I started this habit with.
Learning on a transmission with >6 speeds is hard mode, they do take a little more thinking with the gear pattern than in a car. Synchro versions are not that hard if you're used to a regular manual but adding another thing to learn is not ideal when starting out. If it was a non-synchro variant then good luck getting someone to pick that up without a few solid hours of learning time.
If you were being taught by someone used to heavy trucks it makes sense why they didn't tell you to push the pedal right in - on many (all?) non synchro transmissions pushing the clutch all the way in brakes the input shaft and if you're moving you then have to resynchronise it with the gear speed in order to get into gear.
Note you don't actually have to push the clutch in all the way in a car either, all that really matters is getting it past the point where the clutch is fully disengaged. After all the clutch plate is either touching the flywheel to some degree or it's not touching, once it stops making contact pushing it further away doesn't make a difference. When first starting out though it's easier to just push the pedal all the way in - save thinking about finer details until you're comfortable with the basics.
It's the first floor above the ground level (or the first floor that you have to start calling a separate name, because if everything is single level you don't need to specify a floor).
If I'm doing a small shop I'll take a bag in, fill it up as I go, then everything goes out at the checkout and ends up back in the bag. I've never had anyone care about this and I've been doing it for a few years now (ever since the old plastic bags got banned in my area).
The ACT does get a bit cold in winter, but I feel like it's closer to England than Finland (if England was drier and actually got hot in summer anyway). We are after all talking minimums of -5 or -6 for the coldest days in winter and snow normally only settling on the tops of the nearby mountain range (and temporarily at that).
I think the main problem with searching for fediverse posts is not that they're not indexed but the lack of a singular tag to append when you want to search for them. To search for reddit posts it was easy because you could put in your keywords and stick 'reddit' or 'site:reddit.com' onto the end, but now there's too many domains to keep track of and you can't rely on appending 'lemmy' pointing a search engine towards all Lemmy instances, let alone kbin/mbin instances.
Apart from family and my own number about the only one I can think of is the Reading Writing Hotline (1300 655506) due to the sheer amount of their radio ads I've heard over the years while driving around.
Even within family I've only got one left that actually works though - Dad hasn't changed his mobile number since circa 2000 but Mum did at one point and I never remembered her new one.
I do like Whirlpool, an Australian forum primarily centred on technology. It's still active despite the general decline of forums, has a lot of useful info to turn up in searches, and I appreciate how it has remained clean and fast without the visual clutter and wasted data of modern web design.
I've found a plunger useful for a sink occasionally, a bit of back and forth plunging can loosen up a hairball or break a layer of fat/soap scum. On the other hand I've never needed to use a plunger on a toilet - I don't know how much of this is exaggeration on the internet but Australian toilets don't seem to have anywhere near the amount of issues the American designs do.
It'd be interesting to see how much this changes if you were to restrict the training dataset to books written in the last twenty years, I suspect the model would be a lot less negative. Older books tend to include stuff which does not fit with modern ideals and it'd be a real struggle to avoid this if such texts are used for training.
For example I was recently reading a couple of the sequels to The Thirty-Nine Steps (written during WW1) and they include multiple instances that really date them to an earlier era with the main character casually throwing out jarringly racist stuff about black South Africans, Germans, the Irish, and basically anyone else who wasn't properly English. Train an AI on that and you're introducing the chance for problematic output - and chances are most LLMs have been trained on this series since they're now public domain and easily available.
A broken wisdom tooth with one of the parts rubbing against the nerve that passes through that side of the lower jaw. Definitely would not recommend, it did cost me ~$2k to pull those wisdom teeth (or what remained of them for the lower ones) but it was well worth it.
Edit: Found the x-ray image of that tooth, the dentist told me the white line running past the bottom of the broken tooth is a nerve.
